Impulse 3420 Bedienungsanleitung Seite 1

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Impulse 3420 herunter. Impulse 3420 User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 23
  • Inhaltsverzeichnis
  • FEHLERBEHEBUNG
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
COMM+8™
USER MANUAL
Part #3420
Sealevel Systems, Inc. Telephone: (864) 843-4343
PO Box 830 Fax: (864) 843-3067
Liberty, SC 29657 USA www.sealevel.com
Seitenansicht 0
1 2 3 4 5 6 ... 22 23

Inhaltsverzeichnis

Seite 1 - USER MANUAL

COMM+8™ USER MANUAL Part #3420 Sealevel Systems, Inc. Telephone: (864) 843-4343 PO Box 830 Fax: (864) 843-3067 Liberty, SC 29657

Seite 2 - Contents

Card Setup Sealevel Systems COMM+8 Page 7 To select the maximum data rate (460.8K bps) place the jumper in the divide by 1 (silk-screen DIV1) positio

Seite 3 - Figures

Installation Sealevel Systems COMM+8 Page 8 Installation Operating System Installation For Windows Users Start by choosing Install Software at the b

Seite 4 - Introduction

Technical Description Sealevel Systems COMM+8 Page 9 Technical Description The Sealevel COMM+8 provides 8 additional serial ports for terminals, mode

Seite 5

Technical Description Sealevel Systems COMM+8 Page 10 DB-25 Connector Pin Assignments (DB-25 Male) Signal Name Pin # Mode GND Ground 7 TD Transmi

Seite 6 - Card Setup

Technical Description Sealevel Systems COMM+8 Page 11 DB-78 Connector Pin Assignments (DB-78 Female) Port # 1 2 3 4 5 6 7 8 TD 36 12 27 3 7

Seite 7 - IRQ Selection

Specifications Sealevel Systems COMM+8 Page 12 Specifications Environmental Specifications Specification Operating Storage Temperature Range 0º to 50

Seite 8 - Interrupt Mode Options

Appendix A - Troubleshooting Sealevel Systems COMM+8 Page 13 Appendix A - Troubleshooting Serial Utility test software is supplied with the Sealevel

Seite 9 - Clock Modes

Appendix A - Troubleshooting Sealevel Systems COMM+8 Page 14 8. The following are known I/O conflicts: • The 278 and 378 settings may conflict wit

Seite 10

Appendix B – How To Get Assistance Sealevel Systems COMM+8 Page 15 Appendix B - How To Get Assistance Please refer to Troubleshooting Guide prior t

Seite 11 - Installation

Appendix C - Electrical Interface Sealevel Systems COMM+8 Page 16 Appendix C - Electrical Interface RS-232 Quite possibly the most widely used commu

Seite 12 - Technical Description

Contents INTRODUCTION ... 1 OVERVIEW...

Seite 13

Appendix D - Asynchronous Communications Sealevel Systems COMM+8 Page 17 Appendix D - Asynchronous Communications Serial data communications implie

Seite 14

Appendix E - Silk-Screen Sealevel Systems COMM+8 Page 18 Appendix E - Silk-Screen 3.9"7.0"4.2"

Seite 15 - Specifications

Appendix F - Compliance Notices Sealevel Systems COMM+8 Page 19 Appendix F - Compliance Notices Federal Communications Commission Statement FCC - Th

Seite 16 - Appendix A - Troubleshooting

Warranty Sealevel Systems COMM+8 Page 20 Warranty Sealevel Systems, Inc. provides a limited lifetime warranty. Should this product fail to be in go

Seite 17

FEDERAL COMMUNICATIONS COMMISSION STATEMENT...19 EMC DIRECTIVE STATEMENT ...19 WARRANTY.

Seite 18

Introduction Sealevel Systems COMM+8 Page 1 Introduction Overview The Sealevel Systems COMM+8 provides the PC with eight RS-232 asynchronous ports. T

Seite 19

Introduction Sealevel Systems COMM+8 Page 2 For your reference, record installed COMM+8 settings below: Port # Base Address IRQ E12 Port 1 Por

Seite 20 - 5 to 8 Data Bits

Card Setup Sealevel Systems COMM+8 Page 3 Card Setup The COMM+8 contains several jumper straps that must be set for proper operation. Address Selecti

Seite 21 - 3.9"

Card Setup Sealevel Systems COMM+8 Page 4 “PAL” Addressing If header E11 is set to the “PAL” position, the board can be addressed at a customized lo

Seite 22 - EMC Directive Statement

Card Setup Sealevel Systems COMM+8 Page 5 Interrupt Mode Options The COMM+8 will allow each port to have an independent interrupt level or share an i

Seite 23 - Warranty

Card Setup Sealevel Systems COMM+8 Page 6 Set all jumpers to “S” if you are using more than one COMM+8 in a bus or you wish to completely remove the

Kommentare zu diesen Handbüchern

Keine Kommentare