Impulse SCM5B33 Bedienungsanleitung PDF herunterladen (Seite 2)

Visit our website www.dataforth.com

Isolated Analog Signal Conditioning Products

SCM5B

Specifications

Typical at T

=+25°C and +5V power

Model Input (rms)



Output (DC)



Ordering Information

Module

SCM5B33

Input

Signal Range 100mV to 300Vrms, 0 to 5Arms

Standard Frequency Range 45Hz to 1000Hz

Extended Frequency Range 1kHz to 20kHz

Impedance 1 MΩ ±1% shunted by 100pF (-01 thru -05),

0.10Ω (-06), 0.025Ω (-07)

Coupling AC

Protection

(1)

Continuous (-01 thru -05) 300Vrms

Continuous (-06 thru -07) 10Arms

Transient (-01 thru -05) ANSI/IEEE C37.90.1

Transient (-06 thru -07) See note 2

Output

Signal Range 0-5V or 0-10V or 0-1mA or 0-20mA or 4-20mA

Current Limit 1.4mA (0-1mA models), 30mA (0/4-20mA models),

8mA (0-5, 0-10V models)

Voltage Limit ±18V (0-5, 0-10V models)

Resistance 50Ω (0-5, 0-10V models)

Protection Continuous Short to Ground

Ripple and Noise (100kHz) 0.025% Span rms

Accuracy

(3)(4)

Sinusoid

50/60 Hz ±0.25% Span

45Hz to 1kHz ±0.25% Reading Additional Factor

1kHz to 20kHz ±0.75% Reading Additional Factor

Non-Sinusoid

Crest Factor = 1 to 2 ±0.05% Reading Additional Error

Crest Factor = 2 to 3 ±0.15% Reading Additional Error

Crest Factor = 3 to 4 ±0.30% Reading Additional Error

Crest Factor = 4 to 5 ±0.40% Reading Additional Error

Vs. Temperature ±100ppm/°C

Isolation (Common Mode)

Input to Output, Input to Power

Continuous 1500Vrms max

Transient ANSI/IEEE C37.90.1

Output to Power

Continuous 50VDC max

Rejection (50-60Hz Common Mode) 100dB

Response Time (0 to 99%) <400ms

Output Enable Control

Selection Time 6.0µS at C

LOAD

= 0 to 2000pF

Voltage

Max Logic 0 +0.8V

Min/Max Logic 1 +2.4V/+36V

Current 0,1 0.5µA

Loop Voltage +4.2VDC min, +26VDC max, -40°C to +85°C

Load Resistance (maximum) (Loop Voltage - 4.2) / (Loop Current)

Supply Voltage +5VDC ±5%

Current 120mA

Sensitivity ±200ppm/%

Environmental

Operating Temp. Range -40°C to +85°C

ATEX Group II, Category 3 -20°C to +40°C

Storage Temp. Range -40°C to +85°C

Relative Humidity 0 to 95% Noncondensing

Emissions EN61000-6-4 ISM, Group 1

Radiated, Conducted Class A

Immunity EN61000-6-2 ISM, Group 1

R F Performance A ±0.5% Span Error

ESD, EFT, Surge, Voltage Dips Performance B

Dimensions (h)(w)(d) 2.28" x 2.26" x 0.60" (58mm x 57mm x 15mm)

NOTES:

(1) SCM5B33 and SCMPB01, 02, 03, 04, 05, 06, 07, XEV rating only. Backpanels obtained from other sources may have lower ratings.

(2) For 1 to 25 seconds the max allowable transient current rating is √ 2500 / (event time). For less than 1 second,

ANSI/IEEE C-37.90.1 applies with a 0.05

Ω load. For greater than 25 seconds, the 10A rms continuous rating applies.

SCM5B33-01 0-100mV 0-5V

SCM5B33-02 0-1V 0-5V

SCM5B33-03 0-10V 0-5V

SCM5B33-04 0-150V 0-5V

SCM5B33-05 0-300V 0-5V

SCM5B33-06 0-1A 0-5V

SCM5B33-07 0-5A 0-5V

SCM5B33-01B 0-100mV 0-1mA

SCM5B33-02B 0-1V 0-1mA

SCM5B33-03B 0-10V 0-1mA

SCM5B33-04B 0-150V 0-1mA

SCM5B33-05B 0-300V 0-1mA

SCM5B33-06B 0-1A 0-1mA

SCM5B33-07B 0-5A 0-1mA

SCM5B33-01C 0-100mV 4-20mA

SCM5B33-02C 0-1V 4-20mA

SCM5B33-03C 0-10V 4-20mA

SCM5B33-04C 0-150V 4-20mA

SCM5B33-05C 0-300V 4-20mA

SCM5B33-06C 0-1A 4-20mA

SCM5B33-07C 0-5A 4-20mA

SCM5B33-01D 0-100mV 0-10V

SCM5B33-02D 0-1V 0-10V

SCM5B33-03D 0-10V 0-10V

SCM5B33-04D 0-150V 0-10V

SCM5B33-05D 0-300V 0-10V

SCM5B33-06D 0-1A 0-10V

SCM5B33-07D 0-5A 0-10V

SCM5B33-01E 0-100mV 0-20mA

SCM5B33-02E 0-1V 0-20mA

SCM5B33-03E 0-10V 0-20mA

SCM5B33-04E 0-150V 0-20mA

SCM5B33-05E 0-300V 0-20mA

SCM5B33-06E 0-1A 0-20mA

SCM5B33-07E 0-5A 0-20mA



Modules can be ordered with other input/output ranges. Consult factory

for ordering details and specifications.

3. 0V to +5V NONE SCM5B33-01

4. 0V to +10V D SCM5B33-01D

5. 4mA to 20mA C SCM5B33-01C

6. 0mA to 20mA E SCM5B33-01E

7. 0mA to 1mA B SCM5B33-01B

Output Range Part No. Suffix Example





Output Ranges Available

(3) At standard 60Hz factory calibration. Consult factory for

calibration at other frequencies.

(4) For 10-100% rated span. Add 0.25% accuracy error (-02 thru -07) or

1.00% accuracy error (-01) for 0-10% Span measurements. Accuracy

includes nonlinearity, hysteresis and repeatability but not source or

external shunt inaccuracy (if used).

1 2

Kommentare zu diesen Handbüchern

Keine Kommentare

Impulse SCM5B33 Bedienungsanleitung Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Impulse SCM5B33